How soap is prepared???

How soap is prepared?

Introduction




Soaps are the sodium and potassium salts of long chain fatty acids that are generally
made by saponification (alkaline hydrolysis) of natural fats, such as animal fats or palm oil.
Prior to World War II, most soap was prepared in the home by boiling animal fat with lye
(commercial sodium hydroxide). Soap is not particularly good for cleaning in hard water (water
with high concentrations of Ca2+, Mg2+ and/or Fe3+ ions) because it forms insoluble complexes
with divalent (or trivalent) cations. Organic sulfonic acid and phosphoric acid salts, commonly
known as detergents, were found to be much more effective cleaning agents because they do not
readily form insoluble complexes with the ions in hard water. Modern cleansers labeled "soft
soap" are, in fact, detergents rather than soap. Check the labels for ingredients of some cleansers
you have around the home, including shampoo.
The phosphate detergents caused environmental problems in waterways, not because they
are toxic, but because they are nutrients and resulted in an overabundance of plant growth, or
algal blooms. Consequently phosphate detergents have been replaced with other alternatives.
Today there are a wide variety of synthetic detergents available for various purposes. Some
representative detergents and a soap are shown below.
In this experiment you will prepare soap from a fat and determine some of its properties
relative to a detergent. 

Materials and Reagents


Shortening, lard or coconut oil, 30% NaOH solution, 95% ethanol, 400 mL beaker, 125
mL Erlenmeyer flask, ice, universal pH paper, 1 % detergent (sodium dodecylsulfate) solution,
1% calcium chloride solution, filter paper, filtration apparatus, used pump oil.


Procedure

Preparation of Soap.
1. Add about 150 mL water to a 400 mL beaker and heat the water with your burner to
about 85EC. You will need to mount a clamp above the beaker to hold the Erlenmeyer
flask (see below) upright in the water bath.
2. Add about 3 g (approx. a level, not heaping teaspoon) of shortening, coconut oil, or lard
to a small beaker and dissolve it in 25 mL of 95% ethanol. Do not use too much fat or
you will need more ethanol to dissolve it.


CAUTION!! SODIUM HYDROXIDE SOLUTION IS VERY CAUSTIC. AVOID
GETTING IT ON YOUR SKIN OR CLOTHING. WASH IT OFF IMMEDIATELY
WITH PLENTY OF WATER.

3. When the fat is completely dissolved, pour the solution into a 125 mL Erlenmeyer flask
and add 15 mL of 30% NaOH solution. Swirl the flask to mix the solution and add a few (3
to 5) boiling chips (Boilezer) to the flask.4. Place the flask containing the fat solution in
the water bath and fasten it with a clamp to hold it upright in the water bath. Place a
small watch glass over the mouth of the flask to minimize evaporation of the alcohol. Place
an ice cube in the watch glass to more effectively condense the alcohol.
5. Allow the the fat-alcoholic NaOH solution to boil for at least 30 min. [Note: do not boil
the water in the water bath]. If you observe undissolved fat in the flask, add a little
more ethanol to the flask and stir to dissolve the fat. Do not allow the hot water bath to
get too hot, keep it just hot enough to have controlled boiling of the fat solution.
6. While the saponification proceeds, prepare a salt solution by completely dissolving 20 g
NaCl in 100 mL deionized water in a 250 mL beaker. After the salt completely
dissolves, transfer about half of this salt solution to another beaker and place both beakers of salt solution on ice to cool them.
7. After 30 min, test the fat solution to see if saponification is complete by placing a few
drops of the solution in a test tube of deionized water. If you see fat droplets float to the
top, the saponification is not complete and allow it to boil for an additional 10 min.
8. When saponification is complete, carefully pour the hot reaction mixture into one beaker
of salt solution and stir for a minute or two. Place the mixture on ice to cool it before
filtering.
9. Set up a suction filtration apparatus with a Buchner funnel and filter paper (see Appendix
I for a diagram of the vacuum filtration apparatus). Filter the mixture from step 8, and
wash the soap (remaining in the Buchner funnel) twice with ice cold salt water (from the
second beaker). Draw air through the soap for a few minutes to remove most of the
water.
10. Remove the soap cake from the Buchner funnel and save it for the following tests.












                                                       ~~end~~

Preparation of soap

Preparation of Soap

                                                             

                                                                   By Umesh Kumar

Introduction

            Soap, from a chemical standpoint, is a salt (or a mixture of salts) of fatty acids. As with all salts, soap contains a positive ion, usually Na⁺ or K⁺, and a negative ion, usually the anions of long-chained carboxylic acids obtained by the hydrolysis of animal or vegetable fats. These fatty acids, of which there are about 20 naturally occurring members, are carboxylic acids containing 14, 16, or 18 carbon atoms in an unbranched chain. The even numbered chains result from the

fact that fats are synthesized in cells by the polymerization of a 2-carbon acetate unit.

            In addition to the normal (straight chain) saturated acids, there occur several with hydroxyl groups, and/or one or more double bonds in the carbon chain. the presence of unsaturation (double bonds) in molecules of fatty acids, fats, or soup tend to lower the melting point of these compounds and to cause them to be in the liquid state at room temperature. Thus, vegetable fats are relatively unsaturated and liquid under the ordinary conditions, while animal fats, being relatively more saturated, are solid, or semi-solid, at the same temperature. For this reason, vegetable fats are commonly refereed to as vegetable oils. (We say relatively saturated, or unsaturated because both vegetables oils and animal fats contain saturated and unsaturated chains). The reason why double bonds lower the melting point of a fatty acid chain, is that the sections of the chain attached to the double bond are attached cis-wise to each other (probably because the double bond cis configuration produces a bent chain which does not easily adhere to a neighboring chain by a Van der Waals attraction hence a lower temperature (lower mobility) is required for these molecules to adhere in order to form a solid crystal lattice. It is interesting to note, that straight chained carboxylic acids having an odd number of carbon atoms melt lower than even chained acids of comparable molecular weights.

            The most commonly encountered fatty acids in natural fats are given below:

            Saturated Acids

               Lauric Acid (Dodecanoic Acid)

                       

                        CH₃-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-COOH

                        Myristic Acid (tetraderanoic Acids)

                   CH₃-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-COOH

                        Palmitic acid (hexadecanoic acid)

               CH₃-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-COOH

                        Stearic acid (octadecanoic acid)

 CH₃-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-COOH

                                    Unsaturated acids:

                                                Oleic acid (octadec-9-enoic acid)

           

CH₃-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH=CH- CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-COOH                

Linoleic acid (octadec-9, 12-dienoic acid)

CH₃-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH=CH- CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-CH₂-COOH

            All fats are esters (though, not all esters are necessarily, fat!) of the trihydroxy alcohol, glycerin, and fatty acids. Since each molecule of fat contains three ester groups, fats are often referred to as triglycerides to distinguish them from other materials having a fatty or greasy texture, such as waxes (mono esters of long chain alcohols are carboxylic acids) mineral oil, and petroleum jelly (long-chain hydrocarbons).

            If R-COOH represents a generalized fatty acid (R is a hydrocarbon chain of 13, 15, or 17 carbons) then, the general formula for a fat is

                                               

Note that the fatty-acid residues in a typical fat molecule are usually different! Fats from different sources have different percentages of the common fatty acids, and can be distinguished from one another by a quantitative analysis of these constituents.

            Soap is prepared by hydrolyzing a fat under alkaline (basic) conditions. The reaction is called saponification, and produces one molecule of glycerin and three molecules of soap, for each molecule of fat taken.

                       

The fats and oils most commonly used in soap preparation are lard and tallow from animal sources, and coconut, palm and olive oils from vegetable sources.

            Tallow and lard are the fats separated from solid beef fat (suet) and hog fat, by the process of rendering. Rendering consists of boiling the animal fat in a pot with an equal volume of water until a layer of melted fat collects on top. (when the animal tissue is heated, the fat in the cells melts, expands, ruptures the cell membrane- and then flows out. Since the fat is immiscible with water, and has a lower density, it forms a floating layer on the top of the

water in the pot.) the rendered fat is then drawn off, and allowed to solidify by cooling.

            The length of the hydrocarbon chain and the number of double bonds in the carbonylic-acid portion of the fat or oil determine the properties of the resulting soap.  For example, a salt of a saturated, long-chain acid makes a harder, more insoluble soap.  Chain length also affects solubility. Tallow is the principal fatty material used in soap making, with coconut or palm oil blended in, to produce a softer (more soluble) soap which will readily lather.  Soaps made with KOH (caustic potash) instead of NaOH (caustic soda) are liquid rather than solid, at room temperature. (potassium salts have a lower melting point than sodium salts.)

            Toilet soaps are generally carefully washed free of any remaining alkali used in the saponification procedure to avoid irritation and drying of the skin. As much glycerine as possible is usually left in the soap, and perfumes, coloring, and medicinal agents are sometimes added. Also added, are antioxidants to prevent the soap from turning rancid. Many soaps are superfatted, i.e. not all of the fat is hydrolysed, in order that the final soap have some fat remaining to lubricate and smooth dry and sensitive skin.

            Besides tallow and coconut oil, there are many other natural fats and oils which can be economically employed to make soaps of  varying degrees of quality. The less pure the raw material is, the more likely the soap will have an off-color (generally yellow or brown), and an undesirable odor. (impure fats are sometimes treated with bleaching agents before saponification, but this adds to their cost.) Examples of such other starting materials in soap manufacture are: coconut oil, palm oil, olive oil, cottonseed oil, sesame oil, corn oil, Soya bean oil, hydrogenated vegetable oils, rosin, naphthelinic acids, and greases made from animal skins, bones, tankage and garbage. The lower grades of soaps are used as yellow laundry soap, soap powders, cleansers, and industrial soaps.

            Below is a short glossary of terms employed to describe special types of soap:

Castile soap --  a mild soap originally made in Spain with pure olive oil. Today many “castile” soaps are made with other vegetable oils. Castile is a marvelous cleanser, producing a rich lather.

Cream soaps – soaps containing cold cream materials, moisturizers and emollients. Cream soaps are particularly good for dry and delicate skin

Deodorant soaps – soaps to which antibacterial agents have been added to reduce odor-causing bacteria.

Floating soaps – soaps having air bubbles incorporated to lower the density. This causes the bar to float.

Hypo-allergenic soaps – Mild formula soaps, low in potential irritants. They usually produce a poor lather.

Medicated soaps – soaps containing medications such as tar, sulphur, or antibacterial ingredients, used to treat acne and other skin disorders. Medicated soaps require through rinsing and are not recommended for sensitive skin.

Milled soaps – these are the most commonly used, mass produced soaps. Milling refers to the mixing of color, perfume and soap flakes.

Oatmeal soap – A rough –textured soap to which oatmeal has been added as a mild abrasive and lather. Good for oily, dry, and normal skin.

Procedure

Two procedures for soap making are given, a “cold” and a “hot” process. The cold process, suitable for homemade soaps, produces soap bars which retain the glycreine by-product, and if the amount of alkali employed in the saponification is limited, an excess of fat (superfatted). The hot process, more suitable for laboratory or industrial preparation, yields a more chemically pure powder; by-products and excess starting materials are separated.

I.  Cold process

            You must wear goggles or glasses.

            When using a thermometer in this experiment, never use it to stir liquids. Instead, use a fire polished glass rod. to properly measure the temperature of a liquid, hold the thermometer so that its bulb is suspended in the center of the liquid while reading the mercury level. If the liquid is being heated on a hot plate, do not the thermometer bulb to rest on the bottom of the container, as it will then be overheated. Remove the thermometer from the container after each reading. Note: the thermometer supplied does not require shaking down before or after reading. Plug in a hot plate and set to high.

Weigh a 150 ml beaker on the trip scale and add 8g of NaOH pellets to it.  Handle NaOH with care as NaOH can burn the skin and is especially harmful to the eyes.  In the hood, add 25 ml of cold water to the beaker.  Stir the mixture of NaOH pellets and water, until a clear solution results.  Caution: the beaker will become very hot as the NaOH dissolves.

Weigh a 250ml beaker on the trip-scale and add 58g of fat (Crisco vegetable shortening works well) to it. Then place the beaker on the hot plate with low heat and with occasional stirring, melt the fat to melt completely.  Warm the melted fat to between 40-50 ^oC.  Remove the fat from the hot plate and add the lye solution to the fat with stirring.  Stir the fat and NaOH mixture continuously and until an emulsion is formed.  Your mixture should look like a thick, light yellow milk shake and should stay emulsified (should not separate into a fat and NaOH layer).  If your emulsion separates, the fat is too hot and needs to cool.  Let the mixture cool on the bench top with occasional stirring until an emulsion, which does not separate, is formed.  You may want to add perfume or other additives at this point.  Pour the emulsion into a plastic cup and place in your drawer for the reaction to run (it takes about 24 hours for the reaction to be complete).  Take the soap home with you and let age for about two weeks.  During this time a powdery layer of NaCO₃ (soda ash) will form on the surface, as residual NaOH reacts with CO₂ in the air while the soap is drying. This powdery layer should be sliced off and the soap is ready to be used.

II.  Hot process

You MUST wear goggles or glasses!

Plug in a hot plate and set it on HIGH. Half fill a 400 ml beaker with hot water from the sink and place on the hot plate. When the water begins to boil, adjust the heat, so that the water boils gently, but continuously.  While waiting for the water to boil, weigh a 250ml Erlenmeyer flask on a triple beam balance and add 10g of fat (Crisco, spry, or lard) to it. In a 150ml beaker prepare 100 ml of a 50-50 solution of alcohol-water, by mixing 50 ml of water and 50 ml of 95% ethanol or methanol.  Weigh another 150 ml beaker on the triple beam balance, and add 10g of NaOH pellets to the beaker.  Handle NaOH with care as NaOH can burn the skin and is especially harmful to the eyes. In the hood, mix the NaOH with 36 ml of the of the 50-50 alcohol-water solution to it. Stir the mixture until a transparent solution is formed.  Caution: the beaker will get very hot as the lye dissolves.

Pour the lye solution into the Erlenmeyer flask containing the fat and mix well using a stirring rod or by swirling with a beaker tongs.  Clamp the Erlenmeyer in the boiling-water bath and with occasional stirring, allow it to cook for at least 30 minutes.  While the mixture boils, some foam will form (due to soap formation).  Try to minimize excessive foaming, by adding small adding small portions of your alcohol-water solution.  The reaction is complete when oil globules are no longer visible when the reaction mixture is stirred.

Half fill a 600 ml beaker with 300 ml of clear (filtered) saturated salt (NaC1) solution and 50 ml of water. Pour the still hot reaction mixture containing soap, glycerine, excess NaOH, and alcohol into the salt solution.  Stir the resulting mixture and allow to stand for 5-10 minutes. The soap will collect as a white layer on the surface of the salt water in the beaker.

Prepare a suction trap from the vacuum flask, which will be used later to filter the soap preparation. Bend a long piece of glass tubing into a right angle (instructor will demonstrate), and push one leg of the bend through a one-hole rubber stopper fitted for the mouth of the flask.  When inserted, the glass tube should extend to about ½ inch from the bottom of the flask. The exposed leg of the bend should be cut off at about 3 inches from the bend, and, by means of a piece of rubber connector tubing, be attached to a 12-inch length of glass tubing. The side-arm of the vacuum flask is now connected to the vacuum outlet with pressure tubing.  When the suction is turned on, this device will act like a vacuum cleaner, sucking up liquid instead of dust.

Be sure the suction is OFF, before proceeding. Bring the beaker containing the soap preparation next to the suction trap, and place the “spout” of the trap into the beaker having it touch the bottom.  Slowly turn on the suction, and watch the bottom (aqueous) layer being drawn into the vacuum flask. Draw off most, but not all, of the bottom layer. Be ready to stop the suction instantly, if it appears that some of the soap crystals are being sucked up. You can stop the suction quickly by pulling the pressure tubing away from the outlet, then turning off the vacuum. Caution: At no time should the vacuum flask be allowed to fill more than half-the trap, and pour out its contents.

     When most of the aqueous layer in the beaker has been drawn off, filter the remaining mixture of soap and liquid through a Buchner funnel (with filter paper attached ) to the suction flask. Wash the crystals on the filter with 5 ml portions of ice-cold water. Press out any remaining moisture from the cake of filtered crystals on the funnel with the flat end of a clean cork, or the clean bottom of a small beaker. Allow the product to suck dry for 10-15 minutes.

     Turn off the suction, detach the Buchner funnel, and with the help of a clean spatula, transfer the soap crystals to a large sheet of smooth paper. Pick up the sheet and slide the cystals into a clean, dry 150 ml beaker. Leave the beaker stand, uncovered in your drawer for several days to air-dry the product.

     Weight the soap powder, determine the yield, and hand it to your instructor.

   

                                                   ~  end  ~